spare wheel RENAULT TWINGO RS 2009 2.G Chasiss Workshop Manual

31A-8
FRONT AXLE COMPONENTS
Front brake calliper: Removal - Refitting
EQ UIPMENT LEVEL EA0 or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA5
or EQUIPMENT LEVEL EAG or EQUIPMENT LEVEL EZ2 or EQUIPMENT LEVEL EZ4
31A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) .
aFit the pedal press to the brake pedal to limit the
outflow of brake fluid.
aUnlock the steering column.
aRemove the front wheel on the side concerned (see
35A, Wheels and tyres, Wheel: Removal - Refit-
ting, page 35A-1) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnlock the brake hose (1) on the brake calliper.
aRemove the brake pads (see 31A, Front axle com-
ponents, Front brake pads: Removal - Refitting,
page 31A-1) . Equipment required
pedal press
Tightening torquesm
guide pin bolts34 N.m
brake hose17 N.m
Note:
The callipers supplied as spare par ts are pre-filled
with br ake fluid.
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.
119214
WARNING
In order not to damage the brake hose:
-do not tension the hose,
-do not twist the hose,
-check that there is no contact with the sur-
rounding components.

35A-10
WHEELS AND TYRES
Tyre pressure: Identification
35A
INFLATION
The pressure values given are « motorway » pres-
sures.WARNING
If checking the pressure when hot, increase the tyre
inflation pressure by 0.2 to 0.3 bar above the rec-
ommended pressure.
Engine Wheel rim TyreTyre inflation pressure when cold (bar)
Front Rear emergency
spare wheel
D4F
D7F5.5 J 14165/65 R14 79T
2.2 2.0 2.2 175/65 R14 82 T
6 J 15 185/55 R15 82H
K9K5.5 J 14165/65 R14 79T 2.3 2.1 2.3
175/65 R14 82 T
2.2 2.0 2.2
6 J 15 185/55 R15 82H

37A-56
MECHANICAL COMPONENT CONTROLS
Clutch circuit: Bleed
JH3 or JR5
37A
Bleed screw with two clips.
aTo open the bleed screw, lower the clip (6) and lift
the clip (7) while pulling by one notch.
III - BLEED PROCEDURE IF NO PARTS OF THE
HYDRAULIC CIRCUIT ARE REMOVED
1 - Bleed using the ARC50.
aKeep the clutch pedal in the upper position using a
strap attached to the steering wheel to ensure conti-
nuity of the hydraulic circuit during the bleed opera-
tion.aConnect the brake circuit bleeding device (after
having received Renault approval) to the master cyl-
inder reservoir (see the instructions for the equip-
ment).
aRemove the bleed plug from the clutch slave cylin-
der.
aConnect a transparent pipe to the bleed hole running
to an empty container placed under the bleed hole.
aOpen the bleed screw.
aOpen the circuit between the bleeding device and
the brake fluid reservoir.
aLet the brake fluid run until all air bubbles have been
released.
aStop the bleeding device to dump the pressure in the
clutch circuit.
aClose the bleed screw.
aRemove the transparent pipe from the bleed hole.
aRefit the bleed plug.
aTop up the brake fluid level in the master cylinder
reservoir after disconnecting the bleed device.
aDisengage and engage the clutch quickly around
twenty times.
aCheck that the clutch system is operating correctly.
aRepeat the bleed operation if necessary.
aCheck the adjustment of the switch. (see 37A, Me-
chanical component controls, Clutch pedal
switch: Removal - Refitting, page 37A-52) (37A,
mechanical control elements).
113732
Note:
Ta k e c are not to disrupt the adjustment of the
clutch start of travel switch.

37A-57
MECHANICAL COMPONENT CONTROLS
Clutch circuit: Bleed
JH3 or JR5
37A
2 - Bleed using a new syringe.
aKeep the clutch pedal in the upper position using a
strap attached to the steering wheel to ensure conti-
nuity of the hydraulic circuit during the bleed opera-
tion.
aRemove the bleed plug from the clutch slave cylin-
der.
aConnect a transparent pipe of sufficient length to the
bleed hole (at least thirty centimetres) in order to
place it at the same height as the reservoir.
aOpen the bleed screw.
aFill the brake fluid master cylinder reservoir until
brake fluid flows out of the bleed screw.
aConnect a new hydraulic circuit bleed syringe
filled with a useful volume of 60 ml of approved
brake fluid to the end of the transparent pipe.
aSlowly inject the entire contents of the syringe into
the hydraulic clutch circuit without injecting any of
the air from the top section of the syringe.
aClose the bleed screw.
aRemove the transparent pipe from the bleed hole.
aRefit the bleed plug.
aTop up the brake fluid level in the master cylinder
reservoir.
aDisengage and engage the clutch quickly around
twenty times.
aCheck that the clutch system is operating correctly.
aRepeat the bleed operation if necessary.
aCheck the adjustment of the switch. (see 37A, Me-
chanical component controls, Clutch pedal
switch: Removal - Refitting, page 37A-52) (37A,
mechanical control elements).IV - BLEED PROCEDURE IF PARTS OF THE
HYDRAULIC CIRCUIT ARE REMOVED.
a
Note:
Take care not to disrupt the adjustment of the
clutch start of travel switch.
Note:
The transparent pipe must remain at the same
height as the master cylinder reservoir to prevent
air from entering inside the clutch circuit.
WARNING
The master cylinder pipe must be disconnected
from its take-off point on the br ake fluid reservoir,
to avoid any foreign matter penetrating inside the
hydraulic brake circuit.
WARNING
Prepare for the fl ow of fluid and protect the sur-
rounding components.
Note:
Prefill the hydraulic circuit pipe equipped with a
filter.
Position the filter head facing downwards to
ensure that it fills.

37A-59
MECHANICAL COMPONENT CONTROLS
Clutch circuit: Bleed
JH3 or JR5
37A
aPrefill the hydraulic tappet using the new syringe (by
gravity).
aRefit the part(s) concerned.V - BLEED PROCEDURE AFTER A REMOVING A
COMPONENT OF THE HYDRAULIC CIRCUIT.
aKeep the clutch pedal in the upper position using a
strap attached to the steering wheel to ensure conti-
nuity of the hydraulic circuit during the bleed opera-
tion.
aRemove the bleed plug from the clutch slave cylin-
der.
aConnect a transparent pipe of sufficient length to the
bleed hole (at least thirty centimetres) in order to
place it at the same height as the reservoir.
aOpen the bleed screw.
aFill the brake fluid master cylinder reservoir until
brake fluid flows out of the bleed screw.
aConnect a new syringe containing 60 ml of ap-
proved brake fluid to the end of the transparent pipe.
aSlowly inject the entire contents of the syringe into
the hydraulic clutch circuit without injecting any of
the air from the top section of the syringe.
aClose the bleed screw.
aRemove the transparent pipe from the bleed hole.
aRefit the bleed plug.
aTop up the brake fluid level in the master cylinder
reservoir.
aDisengage and engage the clutch quickly around
twenty times.
aCheck that the clutch system is operating correctly.
aRepeat the bleed operation if necessary.
aCheck the adjustment of the switch. (see 37A, Me-
chanical component controls, Clutch pedal
switch: Removal - Refitting, page 37A-52) (37A,
mechanical control elements).
141809
Note:
Take care not to disrupt the adjustment of the
clutch start of travel switch.
Note:
The transparent pipe must remain at the same
height as the master cylinder reser voir to prevent
air from enter ing inside the clutch circuit.